<tr id="jha7x"></tr>
<th id="jha7x"><address id="jha7x"></address></th>

    <big id="jha7x"></big>
    1.  
       
      聯系我們
      首頁 >> 新聞資訊 >> 新聞中心 >> 濟南恒思盛大臥式拉力試驗機數據顯示窗口介紹

      濟南恒思盛大臥式拉力試驗機數據顯示窗口介紹

           臥式電子拉力試驗機的控制系統主要包括菜單欄,數據顯示窗口,曲線顯示窗口,控制窗口。每個窗口都有各自特殊的功用,之前我們介紹過摩擦磨損試驗機的控制系統。
      Control system of horizontal electronic tensile testing machine mainly includes the menu bar, data display, curve display window, window control. Each window has its own special function, we introduced the control system of friction wear testing machine.
      該系列試驗機的控制系統與其基本類似,但拉伸試驗和摩擦試驗測量的數據不一樣,因此數據窗口也是不相同的。萬能拉力試驗機摩擦試驗所要顯示的數據包括摩擦力,轉速,溫度,報警等,而拉伸試驗所要顯示的數據如下:
      A control system of the test series and their basic similar, but the tensile test and friction test measurement data are not the same, so the data window is not the same. Universal tensile testing machine friction test to display the data include friction, speed, temperature, alarm, while the tensile test to display the data as follows:
           第一、負荷值測量顯示單元:實時顯示負荷值的測量值,即試驗過程中不同階段的力值,主要有破型判斷、調零、峰值等,按下調零按鈕顯示值歸零,破型判斷按鈕可切換破斷保護功能,而峰值顯示試樣所能達到的力值。

      First, the load value measurement display unit: real-time display of measured load value, namely, the different stages of the test process, mainly has broken judgment, zero, peak value, press the button to display the value zero zero, broken judgment button can switch breaking protection function, and the peak maximum force specimen can achieve the value.

           第二、位移測量顯示值:實時顯示移動試臺的位移測量值,按下調零按鈕顯示值歸零。

      Second, the displacement measurement display value: real-time display of displacement measurement of mobile testing table values, press the button to display the value zero zero.

           第三、變形測量顯示值:實時顯示引伸計標距內試樣的變形測量值,按下調零按鈕顯示值歸零;當變形值達到試樣變形值要求時,此時可以摘掉引伸計了,在摘掉引伸計之前須按下摘引伸計按鈕使引伸計停止計數,同時,在此期間控制狀態處于”負荷保載”。

      Third, the deformation measurement display value: real-time display of drawing deformation meter gauge inner values of samples, press the button to display the value zero zero; when the deformation value reaches the specimen deformation value requirements, you can remove the extensometer, at the same time in drawing must be pressed to pick off the extensometer button to make the extensometer stop counting, before during this period, control is in the state of "load holding".

          第四、注意:摘下引伸計重新啟動后,位移值代替了變形值,即變形顯示表頭顯示的是位移值!
      時間顯示窗口:其顯示的時間是從按下 啟動 按鈕,當軟件開始采集數據后至試驗結束時的時間。注意:在試驗過程中力、位移、變形等的 調零 按鈕將不起作用。

      Fourth, pay attention to: pick the extensometer is restarted, the displacement value instead of the value of deformation, deformation indicator shows the displacement value!

      Time display window: the display time is from pressing the start button, when the beginning of the end of data collection software to test time. Note: in the process of test force, displacement, deformation of the zero adjustment button will not work.

      產品推薦:數顯式編織袋拉力試驗機 集裝袋拉力試驗機  薄膜拉力試驗機   橡膠拉力試驗機  電線電纜拉力試驗機


      99久久免费国产精精品
      <tr id="jha7x"></tr>
      <th id="jha7x"><address id="jha7x"></address></th>

        <big id="jha7x"></big>